What's new in the Gallery?
Check This thread
Check This thread
MARTIANS!!! Lighted 9" Star Trek Saucer Kitbash is Finished!
Moderators: tay666, Moderators
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-19-15
Black Wash!
I thinned "The Detailer", Black with about 30% Water and brushed it over the Saucer. Then I let it dry overnight and gently wiped the Saucer off with a damp paper towel removing the Wash from the High Spots & leaving it the Low Spots.
I'm going to do a little more Wiping in the Tight areas with a damp Q-Tip and then I will spray on a couple coats of Testors Dullcote.
More Coming...
I thinned "The Detailer", Black with about 30% Water and brushed it over the Saucer. Then I let it dry overnight and gently wiped the Saucer off with a damp paper towel removing the Wash from the High Spots & leaving it the Low Spots.
I'm going to do a little more Wiping in the Tight areas with a damp Q-Tip and then I will spray on a couple coats of Testors Dullcote.
More Coming...
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-22-15
Wash Off!
Here is a photo of the bottom section after "The Detailer" was brushed on.
The next day I washed off the excess Wash with a damp paper towel first and later with damp Q-Tips.
More Coming...
Here is a photo of the bottom section after "The Detailer" was brushed on.
The next day I washed off the excess Wash with a damp paper towel first and later with damp Q-Tips.
More Coming...
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-24-15
Fixing the Bug!
I removed the Bug from the Stapler, then got the Windows out and the Headlights off. Next I need to remove about 1/16" from the bottom of the Body.
I applied a black wash and then sprayed the Wheels with Dullcote.
I cut 1/16" from the bottom of the Body and then Primed it.
Here is the Bug in Model Masters "Grabber Orange".
More Coming...
I removed the Bug from the Stapler, then got the Windows out and the Headlights off. Next I need to remove about 1/16" from the bottom of the Body.
I applied a black wash and then sprayed the Wheels with Dullcote.
I cut 1/16" from the bottom of the Body and then Primed it.
Here is the Bug in Model Masters "Grabber Orange".
More Coming...
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-27-15
Martians on a Stick!
I sprayed the Martians with Gray Filler/Primer.
Next I sprayed them with Tamiya Light Green.
I used Vallejo Flat Red Paint and Tooth Picks to paint the Eyes.
Then I brushed on a Black Wash. After they dried I sprayed them with Dullcote.
More Coming...
I sprayed the Martians with Gray Filler/Primer.
Next I sprayed them with Tamiya Light Green.
I used Vallejo Flat Red Paint and Tooth Picks to paint the Eyes.
Then I brushed on a Black Wash. After they dried I sprayed them with Dullcote.
More Coming...
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-27-1
Man, you are just going to town! This ought to be great fun when you finish!
- Hunter Rose
- Jack of all Trades
- Posts: 472
- Joined: April 22nd, 2013, 7:20 am
- Location: Bedford, UK
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-27-1
Nice one, the aliens look great ira
Your knowledge of scientific biological transmogrification is only outmatched by your zest for kung-fu treachery! ~ Black Dynamite
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-29-15
We Have Lights!
I finally figured out how to do the Lights! There will be Seven Color Changing Lights and 2 Bright White Lights in the Top of the Saucer, there is One Color Changing Light for the Interior and there are Two Green Death Ray Lights in the Underside. Underside and Interior Photos coming later...
I started by wiring the Lights and then I glued them to plastic brackets I made from plastic.
Next I glued all of the Lights in place and added a 9 Volt Battery & Switch. I grouped the Positive Wires together an soldered them. Did the same with the Negative Wires. Then I slipped some Diffraction Film between the Lights and the Windows and taped it in place.
Light Test!
More Coming...
I finally figured out how to do the Lights! There will be Seven Color Changing Lights and 2 Bright White Lights in the Top of the Saucer, there is One Color Changing Light for the Interior and there are Two Green Death Ray Lights in the Underside. Underside and Interior Photos coming later...
I started by wiring the Lights and then I glued them to plastic brackets I made from plastic.
Next I glued all of the Lights in place and added a 9 Volt Battery & Switch. I grouped the Positive Wires together an soldered them. Did the same with the Negative Wires. Then I slipped some Diffraction Film between the Lights and the Windows and taped it in place.
Light Test!
More Coming...
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-30-15
Death Ray Test!
I cut about an inch from the bottom of the Death Ray, so that the Saucer would sit lower.
Then I carved four Slots for the Landing Gear to fit into.
The Test!
More Coming...
I cut about an inch from the bottom of the Death Ray, so that the Saucer would sit lower.
Then I carved four Slots for the Landing Gear to fit into.
The Test!
More Coming...
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-15-1
Thanks Trevor!tay666 wrote:Man, that is looking sharp.
Great seeing it finally coming together.
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-30-15
Martian Cockpit!
Here are the guys glued in place.
Here is a shot with Color Changing Lights in the Center of the Main Screen and below the Console.
More Coming...
Here are the guys glued in place.
Here is a shot with Color Changing Lights in the Center of the Main Screen and below the Console.
More Coming...
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-15-1
Thanks Steve!Scooke123 wrote:Really looking good with some color on it>
Steve
- tay666
- Site Admin
- Prince of Plastic
- Posts: 17534
- Joined: December 8th, 2003, 11:20 am
- Location: Conneaut Ohio
- Contact:
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-30-1
Wow!
These latest updates are just mind-blowing.
This project is really coming together.
These latest updates are just mind-blowing.
This project is really coming together.
Trevor Ylisaari
Check out My Prehistoric Scenes site and forum
"Nothing like a trail of blood
To find your way back home."
WANTED - Bat Rider - produced by Wraiths
Check out My Prehistoric Scenes site and forum
"Nothing like a trail of blood
To find your way back home."
WANTED - Bat Rider - produced by Wraiths
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-15-1
Thanks Hunter!Hunter Rose wrote:Really dig the death ray, looking very cool ira!
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 6-8-15
Finished the Bug!
Martians View! That is a small VW Decal...
I glued in the Windows. Then I Hot glued in a piece of Diffraction Film, to improve the appearance of the Lights. Next I glued the Wheels into the Wheel Wells.
Then I cut 2 lengths of Aluminum Tubing and glued them in 2 groves I filed in the back.
More Coming...
Martians View! That is a small VW Decal...
I glued in the Windows. Then I Hot glued in a piece of Diffraction Film, to improve the appearance of the Lights. Next I glued the Wheels into the Wheel Wells.
Then I cut 2 lengths of Aluminum Tubing and glued them in 2 groves I filed in the back.
More Coming...
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 6-9-15
On the Road Again!
These are metal Covers for Electric Stove Burners. I think we got them a Dollar Store. I drilled a hole off center and painted one flat black.
I used Stripping Tape to make the Lines on the Highway.
Next I glued some "Earth", "Autumn Grass" and "Bushes" to the side of the Road. I got the Greenery from the Train Dept. at the Hobby Shop.
More Coming...
These are metal Covers for Electric Stove Burners. I think we got them a Dollar Store. I drilled a hole off center and painted one flat black.
I used Stripping Tape to make the Lines on the Highway.
Next I glued some "Earth", "Autumn Grass" and "Bushes" to the side of the Road. I got the Greenery from the Train Dept. at the Hobby Shop.
More Coming...
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-27-1
Rocketeer wrote:Man, you are just going to town! This ought to be great fun when you finish!
Thanks!
It is Great Fun...
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 5-27-1
Thanks Hunter!Hunter Rose wrote:Nice one, the aliens look great ira
THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 6-10-15
Bug Light Test!
I ran 2 Color Changing LEDs up through the Hole.
Then I wired them to the Battery Plug and Hot Glued it all in place.
Bug Light Test!
Rear View.
More Coming...
I ran 2 Color Changing LEDs up through the Hole.
Then I wired them to the Battery Plug and Hot Glued it all in place.
Bug Light Test!
Rear View.
More Coming...
- tidroplane
- Master of Masking
- Posts: 772
- Joined: April 11th, 2014, 10:01 pm
- Location: Everett, Wa.
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 6-10-1
Really looking good Ira!
Dave Hawley
Listen to them, children of the night, what music they make!
Listen to them, children of the night, what music they make!
-
- Bishop of Build Ups
- Posts: 3101
- Joined: November 28th, 2007, 8:24 pm
- Location: St Charles, MO
Re: THE MARTIANS ARE COMING!!! 9" Martian Saucer WIP 6-10-1
That Bug looks really cool lit up!!
Steve
Steve
Steve Cooke